Use Common Problems tile press

Use Common Problems tile press

The solution is to replace the impeller on the machine or sanding, we recommend the first method of comparison, and then impeller obstructions removed, we can solve the problem. Providing tile press common problems and solutions, it is a professional tile press common problems and solutions provider.
Tile press more and more important in the construction of the above buildings, cottage construction, building construction, construction of various buildings are inseparable from it. However, due to relatively easy solutions tile press caused by wear and tear, so there is always this or that problem to affect the normal production and manufacturing, so let’s introduce its recurring problems and problems after

IMG 0807 300x200 - Use Common Problems tile press
1, the machine swinging too big reason: Since the digging wheel wear is more wear and tear the place to be, so they would often wear a serious problem, if there is a serious problem of wear, it will cause impeller for obstructions .
2, idle too much resistance causes: material bearing on the inner seal having clogged Solution: The material bearing on the clog out, while checking whether there is a corresponding device material clogging.
3, bearing fever reasons: lack of oil bearing, bearing a fine entry, bearing damage Workaround: bearing lubrication, cleaning bearings or replace bearings.

IMG 0810 300x200 - Use Common Problems tile press
4, the expected product size is too large Cause: The belt is too loose, the nesting population adjustment unreasonable, impeller speed and other issues will affect the quality of the product, so we have to put the particles in a uniform quality of the product to get the raw material stirring time, so after the brick next step only after the proper particle density in order to achieve appropriate standards. Solution: Check the V-belt tension state to regulate the discharge port, the impeller speed, until the desired standard, use Notepad to record speed range to facilitate the proper use of the next.

If you need this type machine you can contact us with email   roofingmachine@zhongtuocn.com

 

color steel composite plate production line equipment in the production process

color steel composite plate production line equipment in the production process

color steel composite plate production line equipment in the production of composite panels forming the demand for accurate and continuous cut, and cut speed and complex speed products in harmony, so the finished cutting machine adopts the leading frequency control and electromagnetic manipulation air manipulation. And selected HMI computer programming, die cutter – punching knife cutter to full speed by the cutter drive multispeed control, first cut all kinds of corrugated composite panels. This unit has two cutting methods, namely die cutter – punching knife and die cutter – cutter, die cutter – punching knife to open a single rate, flat top cut, tongued and grooved boards.
Automatic: use PLC, touch screen, encoder complete control (Note: should be stated when ordering)
Semi-automatic: the choice of setting foot length of pull method, the trigger limit switch to control the length of the commodity to complete production.
Users can choose the length of the control method according to demand, control in two ways: semi-automatic and fully automatic
Cut unit operating process is: length – pressing – the random motion of cut – relax – reset.

color steel composite plate production line equipment in the production process 1 - color steel composite plate production line equipment in the production process
According to production needs, often commissioning composite panel production line:
1. Plant: height greater than 5500mm length of more than 40000mm,
2. Foundation: Concrete should be flat ground
3. equipment and tools: user-owned 3KW, 10Mpa 1 compressor station, φ10 several trachea, 300mm rectangular device 2, 300mm ruler 2, two pliers, a variety of open-end wrench 1 set, hex wrench 1 set.
4. Power: Three-phase five-wire line a total capacity of 35KW
5. Lifting: lifting the weight of five tons of single-beam lane 1, the effective stroke is 27M. Hook Ground> 4000mm.
6. Operator: The operator of 4 to 5, 4 to 5 support staff.
7. Materials and specifications: metal color plate width: 1200mm or 1000mm thickness: 0.2 ~ 0.6mm
Composite panels pipeline color plates each volume should be less than 5T, the outer diameter of not greater than 1300mm, inner membrane pore size of φ600mm or φ500mm.

color steel composite plate production line equipment in the production process - color steel composite plate production line equipment in the production process